With pinball making a substantial revival throughout the country, Gentle Giant desires to make sure that these traditional, lovely machines remain damage-free while being carried. Oh, and we want the individuals moving them to be safe, too.
At first glimpse, pinball makers can appear intimidating to move since of their fragility, weight, and size. Fortunately, our proficient Giants have a couple of tricks up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox
The bulk of modern pinballs (made in the last Twenty Years approximately) have a hinge system which allows the headbox to be folded down. Early pinball devices had their headboxes bolted on, utilizing either two or four bolts. All Electro-Mechanical pinballs utilize this system, in addition to the early Solid State devices.
Later on machines have hinges and use a locking system to keep the headbox upright. There might also be 2 bolts inside as included safety, in case the latch is broken or inadvertently un-latched.
For Electro-Mechanical pinball makers, you need to eliminate the headbox rear gain access to panel to get to the bolts and plugs inside. Normally this panel has a lock on it to keep it in location, but in time the secret might have been lost. On a regular basis, there is a screw keeping this panel in location.
As soon as inside, eliminate the bolts and disconnect the big connectors that have electrical wiring decreasing into the maker. You may wish to identify these adapters to put them back in the best area, however they ought to be various sizes, making it hard to plug back incorrectly.
You can now eliminate the headbox entirely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will assist keep the back glass in location.
Early Solid State Pinballs
For early Solid State Pinballs, you will require to get rid of the back glass. There is a lock located on the headbox in one of three areas: the left-hand side at the top, right-hand side at the leading or on top of the headbox in the center.
As soon as unlocked, eliminate the back glass by raising it up using the lift channel (at the bottom of the glass), and then pull it out from the bottom.
Then, open the back box light panel by lifting the latch located on either the left-hand side or right-hand side. The panel can now swing out towards you, and provide you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs need you to raise up the lamp panel in order to swing it open.
Now that you are inside, you can eliminate the bolts, and any plugs that have wires decreasing into the maker. You may wish to label these plugs to put them back in the best area. You might not have to remove the plugs, as the electrical wiring must be long enough to permit the headbox to be folded down.
At this point, you can lock up the lamp panel and replace the back glass.
Modern Strong State Pinballs
For Data East, Sega, and Stern Modern pinballs, there is a turnable lock system situated at the back of the headbox. Using the supplied key, turn the lock 90 ° counter-clockwise.
For Williams, Bally, and Gottlieb, you can quickly unlatch the back box at the back of the maker. This is a basic setup and requires no tools.
If you can now fold down the head box onto the cabinet, you're done. Ensure you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise help keep the back glass in place.
If you can not fold the head box down, then you have to get in. There is a lock situated at the top of the back glass in the center. Use the supplied key to unlock, and eliminate the back glass by raising it up from the bottom, then pulling it out from the bottom.
Next, you will require to remove the display panel. You can do this by lifting it up and out. Open the light panel. There will be a lock situated on either the left-hand or right-hand side. (Some more recent Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).
Remove the two bolts, put the back box back together, and fold down the head box onto the cabinet. Ensure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
Getting rid of the Legs.
Pinball Device legs are held in place by 8 bolts. The contemporary pinballs have captive nuts or threaded plates inside for the bolts to screw into.
However these threaded plates and captive nuts can be harmed, and making use of additional nuts may have been required. If this is the case, you will have to open up the front door of the pinball, slide out the playfield glass, and lift up the playfield.
With the front door (coin door) click to read more open, move the lock down bar latch across and eliminate the lock down bar. Then move out the playfield glass, and put in a safe location. Next, raise the playfield by positioning your hand where the ball drains pipes, and raise the playfield up.
You need to now have access to any nuts that might have been utilized. As soon as any nuts have been removed, replace the playfield glass and lock down bar, and lock the front door.
Be sure to mark or remember which legs are for the front and back, as they will be adjusted differently to suit.
Loading the Pinball.
You are now ready to transport your pinball machine. Before you load it, make sure you remove the pinballs so they don't bounce around during transportation.
If you are moving the pinball using a van or SUV, it may be easier to remove the legs just prior to filling the maker. Get a good friend check here to have and assist one of you supporting the pinball, while the other eliminates the front legs.
Ensure you strap the pinball in, as you do not want it moving if you have to stop suddenly!
For Electro-Mechanical pinball machines, you need to remove the headbox moving bulky items rear access panel to get access to the bolts and plugs within. (Some more recent Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs use a fluorescent tube for the back glass lighting).
If you are moving the pinball using a van or SUV, it may be easier to remove the legs simply prior to filling the maker. Get a pal to assist and have one of you supporting the pinball, while the other eliminates the front legs.